A disc is bonded to a prepared testing surface and a partial core is cut around the disc. The disc is then pull off with the handheld hydraulic pulling machine.  The pull-off force register by the electronic gauge is divided by the cross-sectional area of the partial core to obtain the pull-off strength.  

• To evaluate the in-place bond strength between a repair overlay or patch and the substrate
• To evaluate the in-place tensile strength of concrete or other materials
• To evaluate the effect of surface preparation procedures on the tensile strength of the substrate before applying a repair material or overlay
• To evaluate the adhesion of diverse materials like metal plates, tiles, thick coatings, FRP’s, etc., on concrete or masonry surfaces

• Battery powered handheld hydraulic pulling machine with robust steel-aluminum body
• Digital display resolution = 0.1 kN
• Maximum force: 100 kN (about 22 MPa for 75 mm discs)
• Maximum stroke: 6 mm
• Accuracy of measurements: < 2%
• Operating conditions: -10 to 50°C, max. RH = 95%
• Memory capacity: 512 measurements (peak-value, time and date of testing)
• AMIGAS Software for PC communication and printout
• Coefficient of variation of replicate test results for the pull-off test method = 8 – 10% for 75 mm discs and 14 – 16% for 50 mm discs

B-13000 BOND-TEST Pull Machine Kit

Includes:

Item	Order #
Hydraulic pull machine with electronic gauge	L-11-1
AMIGAS printout software	L-13
Cable for printout	L-14
Strength conversion table and manual	B-13001
Counter pressure ring	B-13002
Centering piece	B-13003
Coupling	L-16
Pull bolt	L-17
Bolt handle	L-19
Oil refilling cup	L-24
Oil refilling bottle	L-25
Large screwdriver	C-149
Small screwdriver	C-157
Attaché case	B-13004

BOND-TEST Accessories

B-10000 DSV-Kit: For surface planing, bonding the disc, and attaching the coring rig to produce the partial core without anchoring. Includes:

Item	Order #
Diamond planing wheel unit	B-10010
Suction plate with valve and gauge	B-10020
Two adjustable clamping pliers	B-10030
Centering plate for 75 mm disc Optionally, centering plate for 50 mm disc	B-10040 B-10050
Vacuum pump with hose	B-10060
Wrench, 17 mm	B-10070
Small screwdriver	B-10080
Attaché case	B-10090

B-11000 BOND-TEST Preparation Kit: For removing the center knob after surface planing, cleaning the surface, bonding the discs, and heating the discs in cold weather conditions. Includes:

Item	Order #
Grinder with cup stone	B-11010
Heat gun	B-11020
Steel brush	B-11030
75 mm discs, 6 pcs Optionally, 50 mm discs, 6 pcs	B-11040 B-11050
GRA glue box (Part A: 100 gr + Part B: 2 x 40 ml)	B-11060
Putty knife	B-11070
Araldite epoxy (for acrylic-based materials)	B-11080
Attaché case	B-11090

CORECASE CS-75 Kit: Coring device for producing the partial core. Includes:

Item	Order #
Coring rig with coupling	CC-10
Handles for coring rig, 3 pcs	CC-20
Coring bit, 75 mm x 110 mm	CCB-75/110
Water pump with 2 hoses	CC-30
Clamping pliers, adjustable, 2 pcs	CC-40
Set of anchoring tools, 8 mm	CC-50
8 mm expansion anchors, 20	CC-60
Chisel	CC-70
Hammer	CC-80
Corelifter, 75 mm diameter	CC-90
Wrench, 14 mm	CC-100
Measuring tape	CC-110
Set of spare bearings for coring rig	CC-120
Reinforcement locator	CC-130
Manual	CC-140
Attaché case	CC-150

*Drill machine not included

• Technical datasheet

• Publications

More documentation is available upon request

• ASTM C1583: Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method).

• BS EN 1542: Products and systems for the protection and repair of concrete structures. Test methods. Measurement of bond strength by pull-off.